NXP Semiconductors

PN7160A1HN/C100E

RFID, RF Access, Monitoring ICs

Manufacturer
MPN
PN7160A1HN/C100E
Maximum Clock Speed
13.56 MHz
Package / Case
HVQFN-40(6x6)
Key Attributes
Near Field Communication (NFC) controller

Technical Specifications

TypeDescription
AgreementFeliCa,ISO 14443,ISO 15693,MIFARE,NFC
FeaturesBuilt-in antenna driver;Built-in non-volatile memory;Low power wake-up
Supply Voltage1.65V~1.95V
TypeDescription
Maximum Clock Speed13.56 MHz
InterfaceI2C
Package / CaseHVQFN-40(6x6)

Product Introduction

PN7160 is an NFC controller designed for integration in mobile devices and devices compliant with NFC standards (NFC Forum, NCI).

PN7160 is designed based on experience from previous NXP NFC device generation to ease the integration of NFC technology in mobile devices by providing:

- A low PCB footprint and a reduced external Bill of Material

- An optimized architecture for low-power consumption in different modes (Standby, low-power polling loop)

- A highly efficient integrated power management unit allowing direct supply from an extended battery supply range (2.8 V to 5.5 V).

- Support of an external DC-to-DC like NXP PCA941xA (with x = 0, 1 and 2), to provide more output power.

PN7160 embeds a new generation RF contactless front-end, supporting various transmission modes according to NFCIP-1, NFCIP-2, ISO/IEC14443, ISO/IEC 15693, MIFARE and FeliCa specifications. This new contactless front-end design brings a major performance step-up with on one hand a higher sensitivity and on the other hand the capability to work in active load modulation communication enabling the support of small antenna form factor. It also allows to provide a higher output power by supplying the transmitter output stage from 2.7 V to 5.25 V.

- Enhanced Dynamic LMA (DLMA) to optimize and to enhance load modulation amplitude depending on external field strength. It allows higher range communication distance in card mode.

- Independent LMA phase adjustment by step of 5° for type A, B and F

- Dynamic power control which allows to make use of the maximum power in reader mode without exceeding the maximum power allowed by the standard in 0 distance.

- Card mode receiver sensitivity of 20 mV(p-p)

- Support of single ended receiver

- 1.3 W output transmitter power

Supported transmission modes are listed in Figure 1. For contactless card functionality, the PN7160 can act autonomously if previously configured by the host in such a manner. PICC functionality can be supported without host being turned on.

Features

  • Highly integrated demodulator and decoder
  • Buffered output drivers to connect an antenna with minimum number of external components
  • Integrated RF level detector
  • Integrated Polling Loop for automatic device discovery
  • RF protocols supported: ISO/IEC 14443A, ISO/IEC 14443B PICC mode; ISO/IEC 14443A, ISO/IEC 14443B PCD mode designed according to NFC Forum digital protocol T4T platform and ISO-DEP; FeliCa PCD mode; MIFARE PCD encryption mechanism (MIFARE 1K/4K); NFC Forum tags T1T, T2T, T3T, T4T and T5T; NFCIP-1, NFCIP-2 protocol; NFC Forum certification for P2P, reader and card mode; ISO/IEC 15693/ICODE VCD mode; NFC Forum-compliant embedded T4T for NDEF short record; Support for "Enhanced Contactless Polling" by Apple (PN7161 only)
  • Supported host interfaces: NCI protocol interface according to NFC Forum standardization; I2C-bus High-speed mode; SPI-bus
  • Flexible clock supply concept to facilitate PN7160 integration: Internal oscillator for 27.12 MHz crystal connection; Integrated PLL unit to make use of device reference clock and facilitate PN7160 integration
  • Integrated power management unit: Direct connection to a battery (2.5 V to 5.5 V voltage supply range); Support different low-power states configuration: Hard Power-Down state and Standby state activated by firmware; Autonomous mode when host is shut down
  • Automatic wake-up via RF field, internal timer, and host interfaces
  • Integrated non-volatile memory to store data and executable code for customization: Anti tearing support to recover from tearing events
  • Standards compliance: NFC Forum Device Requirements; NCI 2.0

Applications

  • Mobile devices
  • Portable equipment (personal digital assistants, tablet, notebook, wearable)
  • Consumer devices
  • Smart home gateways

Datasheet

📄 Open Download

Inline preview not available

This datasheet is hosted by the manufacturer, who does not allow it to be embedded. Open the official PDF on www.nxp.com:

Open on www.nxp.com

Compliance & Export Codes

TypeDetails
RoHSROHS3
ECCNEAR99
CNHTS8542399000
USHTS8542390001
TARIC8542399000
TypeDetails
CAHTS8542390000
BRHTS85423999
INHTS85423900
MXHTS8542.39.99

Sourcing Information

Sourcing PN7160A1HN/C100E from China? SZ Procure helps international buyers navigate the Shenzhen electronics market and locate suitable supplier options for specific component requirements.

Our Shenzhen sourcing team can help with supplier sourcing, availability checks and quotation comparison for PN7160A1HN/C100E, then coordinate procurement, supplier screening, inspection and international shipping based on what you need.

Need PN7160A1HN/C100E? Send us your required quantity and specifications for a sourcing check and quotation.