PIC16F18323-I/SL
Microcontrollers
Technical Specifications
| Type | Description |
|---|---|
| Core Processor | PIC |
| Core Bits | 8 |
| Maximum Clock Speed | 32 MHz |
| Flash Memory | 3.5 KB |
| Number of I/O | 12 |
| Flash Type | FLASH |
| Type | Description |
|---|---|
| Adc Bits | 10.0 |
| Oscillator Type | Built-in |
| DAC (Bit) | 5bit |
| Operating Temp | -40°C ~ +85°C |
| Working Voltage V | 3.9 V |
| Package / Case | SOIC-14 |
Product Introduction
PIC16(L)F18313/18323 microcontrollers feature Analog, Core Independent Peripherals and Communication Peripherals, combined with eXtreme Low Power (XLP) for a wide range of general purpose and low-power applications. The Peripheral Pin Select (PPS) functionality enables pin mapping when using the digital peripherals (CLC, CWG, CCP, PWM and communications) to add flexibility to the application design.
Features
- C Compiler Optimized RISC Architecture
- Only 48 Instructions
- Operating Speed: DC – 32 MHz clock input, 125 ns minimum instruction cycle Interrupt Capability
- 16-Level Deep Hardware Stack
- Up to Four 8-bit Timers
- Up to Three 16-bit Timers
- Low-Current Power-on Reset (POR)
- Power-up Timer (PWRT)
- Brown-out Reset (BOR)
- Low-Power BOR (LPBOR) Option
- Extended Watchdog Timer (WDT) with Dedicated On-Chip Oscillator for Reliable Operation
- Programmable Code Protection
- Sleep mode: 40 nA @1.8V, typical
- Watchdog Timer: 250 nA @ 1.8V, typical
- Secondary Oscillator: 300 nA @ 32 kHz
- Operating Current: 8 μA @ 32 kHz, 1.8V, typical; 37 μA/MHz @ 1.8V, typical
- IDLE mode: ability to put the CPU core to Sleep while internal peripherals continue operating from the system clock
- DOZE mode: ability to run the CPU core slower than the system clock used by the internal peripherals
- SLEEP mode: Lowest Power Consumption
- Peripheral Module Disable (PMD): peripheral power disable hardware module to minimize power consumption of unused peripherals
- Configurable Logic Cell (CLC): Two CLCs, Integrated combinational and sequential logic
- Complementary Waveform Generator (CWG): Rising and falling edge dead-band control, Full-bridge, half-bridge, 1-channel drive, Multiple signal sources
- Capture/Compare/PWM (CCP) modules: Two CCPs, 16-bit resolution for Capture/Compare modes, 10-bit resolution for PWM mode
- Pulse-Width Modulators (PWM): Two 10-bit PWMs
- Numerically Controlled Oscillator (NCO): Precision linear frequency generator (@50% duty cycle) with 0.0001% step size of source input clock, Input Clock: 0 Hz < F_NCO < 32 MHz, Resolution: F_NCO/2^20
- Serial Communications: EUSART, RS-232, RS-485, LIN compatible, Auto-Baud Detect, auto-wake-up on start; Master Synchronous Serial Port (MSSP), SPI, I2C_SMBus, PMBus compatible
- Data Signal Modulator (DSM): Modulates a carrier signal with digital data to create custom carrier synchronized output waveforms
- Up to 12 I/O Pins: Individually programmable pull-ups, Slew rate control, Interrupt-on-change with edge-select, Input level selection control (ST or TTL), Digital open-drain enable
- Peripheral Pin Select (PPS): I/O pin remapping of digital peripherals
- Timer modules: Timer0: 8/16-bit timer/counter, Synchronous or asynchronous operation, Programmable prescaler/postscaler, Time base for capture/compare function; Timer1 with gate control: 16-bit timer/counter, Programmable internal or external clock sources, Multiple gate sources, Multiple gate modes, Time base for capture/compare function; Timer2: 8-bit timers, Programmable prescaler/postscaler, Time base for PWM function
- 10-bit Analog-to-Digital Converter (ADC): Up to 11 external channels, Conversion available during Sleep
- Comparator: Up to two comparators, Fixed Voltage Reference at non-inverting input(s), Comparator outputs externally accessible
- 5-bit Digital-to-Analog Converter (DAC): 5-bit resolution, rail-to-rail, Positive Reference Selection, Unbuffered I/O pin output, Internal connections to ADCs and comparators
- Voltage Reference: Fixed Voltage Reference with 1.024V, 2.048V and 4.096V output levels
- High-Precision Internal Oscillator: Software-selectable frequency range up to 32 MHz, ±2% at nominal 4 MHz calibration point
- 4x PLL with External Sources
- Low-Power Internal 31 kHz Oscillator (LFINTOSC)
- External Low-Power 32 kHz Crystal Oscillator (SOSC)
- External Oscillator Block with: Three Crystal/Resonator modes up to 20 MHz, Three External Clock modes up to 32 MHz, Fail-Safe Clock Monitor, Detects clock source failure, Oscillator Start-up Timer (OST), Ensures stability of crystal oscillator sources
Datasheet
Alternative Parts
Common PIC16F18323-I/SL alternatives overseas buyers search for:
- PIC16F18323T-I/SL (request quote)
- PIC16F15323-I/SL (request quote)
- PIC16F15323T-I/SL (request quote)
- PIC16F18324-I/SL (request quote)
- PIC16F18325-I/SL (request quote)
- PIC16F15323-E/SL (request quote)
- PIC16F18325-E/SL (request quote)
- PIC16F18326-I/SL (request quote)
- PIC16LF18323-E/SL (request quote)
- PIC16F18426T-I/SL (request quote)
- PIC16F18426-I/SL (request quote)
- PIC16F18323-E/SL (request quote)
- PIC16F18324T-I/SL (request quote)
- PIC16F18325T-I/SL (request quote)
- PIC16F18324-E/SL (request quote)
- PIC16LF18323-I/SL (request quote)
- PIC16LF18323T-I/SL (request quote)
- PIC16F18326T-I/SL (request quote)
- PIC16F18326-E/SL (request quote)
- PIC16LF15323T-I/SL (request quote)
Compliance & Export Codes
| Type | Details |
|---|---|
| RoHS | ROHS3 |
| ECCN | 3A991A2 |
| Type | Details |
|---|---|
| CNHTS | 8542319090 |
Sourcing Information
Looking for a reliable source for PIC16F18323-I/SL from Microchip Technology? SZ Procure is a China electronics sourcing partner, helping international buyers source components through our supplier network in Shenzhen.
When you need PIC16F18323-I/SL, SZ Procure can look into supplier options, confirm current availability, compare sourcing quotes and handle purchasing, pre-shipment inspection and consolidated shipment from Shenzhen.
Ready to source PIC16F18323-I/SL? Send your requirement through Request a Quote and we'll help check sourcing options and procurement costs.